油缸y型油封型号（油缸油封尺寸怎么量） - 原点资讯

Y形密封圈

油缸y型油封型号,油缸油封尺寸怎么量(1)

油缸y型油封型号,油缸油封尺寸怎么量(2)

结构	Y形密封圈通常由高硬度的丁腈橡胶模压而成，用于液压系统中的活塞、柱塞和活塞杆的密封。当密封圈装入沟槽中，密封唇仅与滑动表面沟槽底部金属相接触,产生一定的预应力，达到密封的效果。在压力的作用下，由于密封唇圆周方向的变形，产生接触压力，随着液体压力的增加，变形和接触压力也随之增大，使Y形圈达到自封的效果
	Y形密封圈的主要缺点是作往复式活塞密封时，容易出现密封圈移位和“反转”现象，内压过高时，也可能发生“胶料挤出”现象
设计要点	①为了使唇能很好地张开起自封作用，常在填料腔上开一小孔，开孔方式如图（b）所示
	②密封圈底部的间隙应尽可能做到最小，以避免在高压下发生胶料挤出现象。当间隙不可能做到最小时，应与挡圈并用，或选用底面上镶有挡圈的专用密封圈
	③Y形圈对偏心载荷和偏心运动的适应性不强。当活塞的运动和受力遇到偏心时,为了避免唇部偏心磨损，常在密封之间设一抗磨环，抗磨环的材料应耐磨和具有自润滑性，故一般用夹布酚醛塑料、尼龙或聚四氟乙烯
	④接融面的粗糙度对Y形圈的寿命和密封性有很大影响，所以一般缸的内壁面粗糙度应庄1.6μm以下，最好经过辊压。活塞杆的密封面，应镀硬铬并抛光，要求粗糙度在0.8μm以下。安装Y形圈的沟槽，也应有粗糙度的限制，侧面应为3.2μm,底面应为1.6~0。4μm
	⑤Y形圈通过的部位，不得有尖角、毛剌，因这些加工痕迹很容易刮伤Y形圈的唇部。为此，在设计时，对孔口和轴端应要求倒角或修圆
	⑥ 户外及外露的油缸所用的Y形圈，必须做防尘、防水设计，避免活塞杆磨损和密封圈老化，并保证活塞密封和油的洁净。防尘可用油封、毡封及其他防尘密封。当外部有冰冻时常在防尘圈之外另加防冰板

活塞L1密封沟槽用Y形橡胶密封圈结构型式、尺寸和公差(摘自GB/T 10708.1-2000)

油缸y型油封型号,油缸油封尺寸怎么量(3)

D	ｄ	L1	外径			宽度			高度
D	ｄ	L1	D1	D2	极限偏差	S1	S2	极限偏差	h	极限偏差
12	4	5	13	11.5	±0.20	5	3.5	±0.15	4.4	±0.2
16	8	5	17	15.5	±0.20	5	3.5	±0.15	4.4	±0.2
20	12	5	21.1	19.4	±0.25	5	3.5	±0.15	4.4	±0.2
25	17	5	26.1	24.4	±0.25	5	3.5	±0.15	4.4	±0.2
32	24	5	33.1	31.4	±0.25	5	3.5	±0.15	4.4	±0.2
40	32	5	41.1	39.4	±0.25	5	3.5	±0.15	4.4	±0.2
20	10	6.3	21.2	19.4	±0.25	6.2	4.4	±0.15	5.6	±0.2
25	15	6.3	26.2	24.4	±0.25	6.2	4.4	±0.15	5.6	±0.2
32	22	6.3	33.2	31.4	±0.25	6.2	4.4	±0.15	5.6	±0.2
40	30	6.3	41.2	39.4	±0.25	6.2	4.4	±0.15	5.6	±0.2
50	40	6.3	51.2	49.4	±0.35	6.2	4.4	±0.15	5.6	±0.2
56	46	6.3	57.2	55.4	±0.35	6.2	4.4	±0.15	5.6	±0.2
63	53	6.3	64.2	62.4	±0.35	6.2	4.4	±0.15	5.6	±0.2
50	35	9.5	51.5	49.2	±0.35	9	6.7	±0.15	8.5	±0.2
56	41	9.5	57.5	55.2	±0.35	9	6.7	±0.15	8.5	±0.2
63	48	9.5	64.5	62.2	±0.35	9	6.7	±0.15	8.5	±0.2
70	55	9.5	71.5	69.2	±0.35	9	6.7	±0.15	8.5	±0.2
80	65	9.5	81.5	79.2	±0.35	9	6.7	±0.15	8.5	±0.2
90	75	9.5	91.5	89.2	±0.35	9	6.7	±0.15	8.5	±0.2
100	85	9.5	101.5	99.2	±0.35	9	6.7	±0.15	8.5	±0.2
110	95	9.5	111.5	109.2	±0.45	9	6.7	±0.15	8.5	±0.2
70	50	12.5	71.8	69	±0.35	11.8	9	±0.15	11.3	±0.2
80	60	12.5	81.8	79	±0.35	11.8	9	±0.15	11.3	±0.2
90	70	12.5	91.8	89	±0.35	11.8	9	±0.15	11.3	±0.2
100	80	12.5	101.8	99	±0.35	11.8	9	±0.15	11.3	±0.2
110	90	12.5	111.8	109	±0.35	11.8	9	±0.15	11.3	±0.2
125	105	12.5	126.8	124	±0.45	11.8	9	±0.15	11.3	±0.2
140	120	12.5	141.8	139	±0.45	11.8	9	±0.15	11.3	±0.2
160	140	12.5	161.8	159	±0.45	11.8	9	±0.15	11.3	±0.2
180	160	12.5	181.8	179	±0.6	11.8	9	±0.15	11.3	±0.2
125	100	16	127.2	123.8	±0.45	14.7	11.3	±0.15	14.8	±0.2
140	115	16	142.2	138.8	±0.45	14.7	11.3	±0.15	14.8	±0.2
160	135	16	162.2	158.8	±0.45	14.7	11.3	±0.15	14.8	±0.2
180	155	16	182.2	178.8	±0.5	14.7	11.3	±0.15	14.8	±0.2
200	175	16	202.2	198.8	±0.5	14.7	11.3	±0.15	14.8	±0.2
220	195	16	222.2	218.8	±0.5	14.7	11.3	±0.15	14.8	±0.2
250	225	16	252.2	248.8	±0.50	14.7	11.3	±0.15	14.8	±0.20
200	170	20	202.8	198.5	±0.50	17.8	13.5	±0.20	18.5	±0.25
220	190	20	222.8	218.5	±0.50	17.8	13.5	±0.20	18.5	±0.25
250	220	20	252.8	248.5	±0.50	17.8	13.5	±0.20	18.5	±0.25
280	250	20	282.8	278.5	±0.90	17.8	13.5	±0.20	18.5	±0.25
320	290	20	322.8	318.5	±0.90	17.8	13.5	±0.20	18.5	±0.25
360	330	20	362.8	358.5	±0.90	17.8	13.5	±0.20	18.5	±0.25
400	360	25	403.5	398	±1.40	23.3	18	±0.20	23	±0.25
450	410	25	453.5	448	±1.40	23.3	18	±0.20	23	±0.25
500	460	25	503.5	498	±1.40	23.3	18	±0.20	23	±0.25

活塞杆L1密封沟槽用Y形橡胶密封圈结构型式、尺寸和公差(摘自GB/T 10708.1-2000)

油缸y型油封型号,油缸油封尺寸怎么量(4)

d	Ｄ	L1	内径			宽度			高度
d	Ｄ	L1	d1	d2	极限偏差	S1	S2	极限偏差	h	极限偏差
6	14	5	5	6.5	土0.20	5	3.5	±0.15	4.6	±0.20
8	16	5	7	8.5	土0.20	5	3.5	±0.15	4.6	±0.20
10	18	5	9	10.5	土0.20	5	3.5	±0.15	4.6	±0.20
12	20	5	11	12.5	土0.20	5	3.5	±0.15	4.6	±0.20
14	22	5	13	14.5	土0.20	5	3.5	±0.15	4.6	±0.20
16	24	5	16	16.5	±0.25	5	3.5	±0.15	4.6	±0.20
18	26	5	17	18.5	±0.25	5	3.5	±0.15	4.6	±0.20
20	28	5	19	20.5	±0.25	5	3.5	±0.15	4.6	±0.20
22	30	5	21	22.5	±0.25	5	3.5	±0.15	4.6	±0.20
25	33	5	24	25.5	±0.25	5	3.5	±0.15	4.6	±0.20
28	38	6.3	26.8	28.6	±0.25	6.2	4.4	±0.15	5.6	±0.20
32	42	6.3	30.8	32.6	±0.25	6.2	4.4	±0.15	5.6	±0.20
36	46	6.3	34.8	36.6	±0.25	6.2	4.4	±0.15	5.6	±0.20
40	50	6.3	38.8	40.6	±0.25	6.2	4.4	±0.15	5.6	±0.20
45	55	6.3	43.8	45.6	±0.25	6.2	4.4	±0.15	5.6	±0.20
50	60	6.3	48.8	50.6	±0.25	6.2	4.4	±0.15	5.6	±0.20
56	71	9.5	54.5	56.8	±0.25	9	6.7	±0.15	8.5	±0.20
63	78	9.5	61.5	63.8	±0.25	9	6.7	±0.15	8.5	±0.20
70	85	9.5	68.5	70.8	±0.35	9	6.7	±0.15	8.5	±0.20
80	95	9.5	78.5	80.8	±0.35	9	6.7	±0.15	8.5	±0.20
90	105	9.5	88.5	90.5	±0.35	9	6.7	±0.15	8.5	±0.20
100	120	12.5	98.2	101	±0.35	11.8	9	±0.15	11.3	±0.20
110	130	12.5	108.2	111	±0.45	11.8	9	±0.15	11.3	±0.20
125	145	12.5	123.2	126	±0.45	11.8	9	±0.15	11.3	±0.20
140	160	12.5	138.2	141	±0.45	11.8	9	±0.15	11.3	±0.20
160	185	16	157.8	161.2	±0.45	14.7	11.3	±0.15	14.8	±0.20
180	205	16	177.8	181.2	±0.60	14.7	11.3	±0.15	14.8	±0.20
200	225	16	197.8	201.2	±0.60	14.7	11.3	±0.15	14.8	±0.20
220	250	20	217.2	221.5	±0.60	17.8	13.5	±0.15	18.5	±0.20
250	280	20	247.2	251.5	±0.60	17.8	13.5	±0.15	18.5	±0.20
280	310	20	277.2	281.5	±0.90	17.8	13.5	±0.15	18.5	±0.20
320	360	25	316.7	322	±0.90	23.3	18	±0.20	23	±0.25
360	400	25	356.7	362	±0.90	23.3	18	±0.20	23	±0.25

活塞L2密封沟槽的密封结构型式及Y形圈、蕾形圈尺寸和公差(摘自GB/T 10708.1-2000)

油缸y型油封型号,油缸油封尺寸怎么量(5)

D	ｄ	L2	Y形圈								蕾形圈
			外径			宽度			高度		外径			宽度			高度
			D1	D2	极限偏差	S1	S2	极限偏差	h	极限偏差	D1	D2	极限偏差	S1	S2	极限偏差	h	极限偏差
12	4	6.3	13	11.5	±0.20	5	3.5	±0.15	5.8	±0.20	12.7	11.5	±0.18	4.7	3.5	±0.15	5.6	±0.20
16	8	6.3	17	15.5	±0.20	5	3.5	±0.15	5.8	±0.20	16.7	15.5	±0.18	4.7	3.5	±0.15	5.6	±0.20
20	12	6.3	21	19.5	±0.25	5	3.5	±0.15	5.8	±0.20	20.7	19.5	±0.22	4.7	3.5	±0.15	5.6	±0.20
25	17	6.3	26	24.5	±0.25	5	3.5	±0.15	5.8	±0.20	25.7	24.5	±0.22	4.7	3.5	±0.15	5.6	±0.20
32	24	6.3	33	31.5	±0.25	5	3.5	±0.15	5.8	±0.20	32.7	31.5	±0.22	4.7	3.5	±0.15	5.6	±0.20
40	32	6.3	41	39.5	±0.25	5	3.5	±0.15	5.8	±0.20	40.7	39.5	±0.22	4.7	3.5	±0.15	5.6	±0.20
20	10	8	21.2	19.4	±0.25	6.2	4.4	±0.15	7.3	±0.20	20.8	19.4	±0.22	5.8	4.4	±0.15	7	±0.20
25	15	8	26.2	24.4	±0.25	6.2	4.4	±0.15	7.3	±0.20	25.8	24.4	±0.22	5.8	4.4	±0.15	7	±0.20
32	22	8	33.2	31.4	±0.25	6.2	4.4	±0.15	7.3	±0.20	32.8	31.4	±0.22	5.8	4.4	±0.15	7	±0.20
46	30	8	41.2	39.4	±0.25	6.2	4.4	±0.15	7.3	±0.20	40.8	39.4	±0.22	5.8	4.4	±0.15	7	±0.20
50	40	8	51.2	49.4	±0.25	6.2	4.4	±0.15	7.3	±0.20	50.8	49.4	±0.22	5.8	4.4	±0.15	7	±0.20
56	46	8	57.2	55.4	±0.25	6.2	4.4	±0.15	7.3	±0.20	56.8	55.4	±0.22	5.8	4.4	±0.15	7	±0.20
63	53	8	64.2	62.4	±0.25	6.2	4.4	±0.15	7.3	±0.20	63.8	62.4	±0.22	5.8	4.4	±0.15	7	±0.20
50	35	12.5	51.5	49.2	±0.25	9	6.7	±0.15	11.5	±0.20	51	49.1	±0.22	8.5	6.6	±0.15	11.3	±0.20
56	41	12.5	57.5	55.2	±0.25	9	6.7	±0.15	11.5	±0.20	57	55.1	±0.22	8.5	6.6	±0.15	11.3	±0.20
70	55	12.5	71.5	69.2	±0.35	9	6.7	±0.15	11.5	±0.20	71	69.1	±0.28	8.5	6.6	±0.15	11.3	±0.20
80	65	12.5	81.5	79.2	±0.35	9	6.7	±0.15	11.5	±0.20	81	79.1	±0.28	8.5	6.6	±0.15	11.3	±0.20
90	75	12.5	91.5	89.2	±0.35	9	6.7	±0.15	11.5	±0.20	91	89.1	±0.28	8.5	6.6	±0.15	11.3	±0.20
100	85	12.5	101.5	99.2	±0.35	9	6.7	±0.15	11.5	±0.20	101	99.1	±0.28	8.5	6.6	±0.15	11.3	±0.20
110	95	12.5	111.5	109.2	±0.45	9	6.7	±0.15	11.5	±0.20	111	109.1	±0.35	8.5	6.6	±0.15	11.3	±0.20
70	50	16	71.8	69	±0.35	11.8	9	±0.15	15	±0.20	71.2	68.6	±0.28	11.2	8.6	±0.15	14.5	±0.20
80	60	16	81.8	79	±0.35	11.8	9	±0.15	15	±0.20	81.2	78.6	±0.28	11.2	8.6	±0.15	14.5	±0.20
90	70	16	91.8	89	±0.35	11.8	9	±0.15	15	±0.20	91.2	88.6	±0.28	11.2	8.6	±0.15	14.5	±0.20
100	80	16	101.8	99	±0.35	11.8	9	±0.15	15	±0.20	101.2	98.6	±0.28	11.2	8.6	±0.15	14.5	±0.20
110	90	16	111.8	109	±0.45	11.8	9	±0.15	15	±0.20	111.2	108.6	±0.35	11.2	8.6	±0.15	14.5	±0.20
125	105	16	126.8	124	±0.45	11.8	9	±0.15	15	±0.20	126.2	123.6	±0.35	11.2	8.6	±0.15	14.5	±0.20
140	120	16	141.8	139	±0.45	11.8	9	±0.15	15	±0.20	141.2	138.6	±0.35	11.2	8.6	±0.15	14.5	±0.20
160	140	16	161.8	159	±0.45	11.8	9	±0.15	15	±0.20	161.2	158.6	±0.35	11.2	8.6	±0.15	14.5	±0.20
180	160	16	181.8	179	±0.60	11.8	9	±0.15	15	±0.20	181.2	178.6	±0.45	11.2	8.6	±0.15	14.5	±0.20
125	100	20	127.2	123.8	±0.45	14.7	11.3	±0.15	18.5	±0.20	126.3	123.2	±0.35	13.8	10.7	±0.15	18	±0.20
140	115	20	142.2	138.8	±0.45	14.7	11.3	±0.15	18.5	±0.20	141.3	138.2	±0.35	13.8	10.7	±0.15	18	±0.20
160	135	20	162.2	158.8	±0.45	14.7	11.3	±0.15	18.5	±0.20	161.3	158.2	±0.35	13.8	10.7	±0.15	18	±0.20
180	155	20	182.2	178.8	±0.60	14.7	11.3	±0.15	18.5	±0.20	181.3	178.2	±0.45	13.8	10.7	±0.15	18	±0.20
200	175	20	202.2	198.8	±0.60	14.7	11.3	±0.15	18.5	±0.20	201.3	198.2	±0.45	13.8	10.7	±0.15	18	±0.20
220	195	20	222.2	218.8	±0.60	14.7	11.3	±0.15	18.5	±0.20	221.3	218.2	±0.45	13.8	10.7	±0.15	18	±0.20
250	225	20	252.2	248.8	±0.60	14.7	11.3	±0.15	18.5	±0.20	251.3	248.2	±0.45	13.8	10.7	±0.15	18	±0.20
200	170	25	202.8	198.5	±0.60	17.8	13.5	±0.20	23	±0.25	201.4	198	±0.45	16.4	12.7	±0.20	22.5	±0.25
220	190	25	222.8	218.5	±0.60	17.8	13.5	±0.20	23	±0.25	221.4	218	±0.45	16.4	12.7	±0.20	22.5	±0.25
250	220	25	252.8	248.5	±0.60	17.8	13.5	±0.20	23	±0.25	251.4	248	±0.45	16.4	12.7	±0.20	22.5	±0.25
280	250	25	282.8	278.5	±0.90	17.8	13.5	±0.20	23	±0.25	281.4	278	±0.60	16.4	12.7	±0.20	22.5	±0.25
320	290	25	322.8	318.5	±0.90	17.8	13.5	±0.20	23	±0.25	321.4	318	±0.60	16.4	12.7	±0.20	22.5	±0.25
360	330	25	362.8	358.5	±0.90	17.8	13.5	±0.20	23	±0.25	361.4	358	±0.60	16.4	12.7	±0.20	22.5	±0.25
400	360	32	403.3	398	±1.40	23.3	18	±0.20	29	±0.25	401.8	397	±0.90	21.8	17	±0.20	28.5	±0.25
450	410	32	453.3	448	±1.40	23.3	18	±0.20	29	±0.25	451.8	447	±0.90	21.8	17	±0.20	28.5	±0.25
500	460	32	503.3	498	±1.40	23.3	18	±0.20	29	±0.25	501.8	497	±0.90	21.8	17	±0.20	28.5	±0.25

活塞杆L2密封沟槽结构型式及Y形圈、蕾形圈尺寸和公差(摘自GB/T 10708.1-2000)

油缸y型油封型号,油缸油封尺寸怎么量(6)

d	Ｄ	L2	Y形圈								蕾形圈
			内径			宽度			高度		内径			宽度			高度
			d1	d2	极限偏差	S1	S2	极限偏差	h	极限偏差	d1	d2	极限偏差	S1	S2	极限偏差	h	极限偏差
6	14	6.3	5	6.5	±0.20	5	3.5	±0.15	5.8	±0.20	5.3	6.5	±0.18	4.7	3.5	±0.15	5.5	±0.20
8	16	6.3	7	8.5	±0.20	5	3.5	±0.15	5.8	±0.20	7.3	8.5	±0.18	4.7	3.5	±0.15	5.5	±0.20
10	18	6.3	9	10.5	±0.20	5	3.5	±0.15	5.8	±0.20	9.3	10.5	±0.18	4.7	3.5	±0.15	5.5	±0.20
12	20	6.3	11	12.5	±0.20	5	3.5	±0.15	5.8	±0.20	11.3	12.5	±0.18	4.7	3.5	±0.15	5.5	±0.20
14	22	6.3	13	14.5	±0.20	5	3.5	±0.15	5.8	±0.20	13.3	14.5	±0.18	4.7	3.5	±0.15	5.5	±0.20
16	24	6.3	15	16.5	±0.20	5	3.5	±0.15	5.8	±0.20	15.3	16.5	±0.18	4.7	3.5	±0.15	5.5	±0.20
18	26	6.3	17	18.5	±0.20	5	3.5	±0.15	5.8	±0.20	17.3	18.5	±0.18	4.7	3.5	±0.15	5.5	±0.20
20	28	6.3	19	20.5	±0.20	5	3.5	±0.15	5.8	±0.20	19.3	20.5	±0.18	4.7	3.5	±0.15	5.5	±0.20
22	30	6.3	21	22.5	±0.25	5	3.5	±0.15	5.8	±0.20	21.3	22.5	±0.22	4.7	3.5	±0.15	5.5	±0.20
25	33	6.3	24	25.5	±0.25	5	3.5	±0.15	5.8	±0.20	24.3	25.5	±0.22	4.7	3.5	±0.15	5.5	±0.20
10	20	8	8.8	10.6	±0.20	6.2	4.4	±0.15	7.3	±0.20	9.2	10.6	±0.18	5.8	4.4	±0.15	7	±0.20
12	22	8	10.8	12.6	±0.20	6.2	4.4	±0.15	7.3	±0.20	11.2	12.6	±0.18	5.8	4.4	±0.15	7	±0.20
14	24	8	12.8	14.6	±0.20	6.2	4.4	±0.15	7.3	±0.20	13.2	14.6	±0.18	5.8	4.4	±0.15	7	±0.20
16	26	8	14.8	16.6	±0.20	6.2	4.4	±0.15	7.3	±0.20	15.2	16.6	±0.18	5.8	4.4	±0.15	7	±0.20
18	28	8	16.8	18.6	±0.20	6.2	4.4	±0.15	7.3	±0.20	17.2	18.6	±0.18	5.8	4.4	±0.15	7	±0.20
20	30	8	18.8	20.6	±0.20	6.2	4.4	±0.15	7.3	±0.20	19.2	20.6	±0.18	5.8	4.4	±0.15	7	±0.20
22	32	8	20.8	22.6	±0.25	6.2	4.4	±0.15	7.3	±0.20	21.2	22.6	±0.22	5.8	4.4	±0.15	7	±0.20
25	35	8	23.8	25.6	±0.25	6.2	4.4	±0.15	7.3	±0.20	24.2	25.6	±0.22	5.8	4.4	±0.15	7	±0.20
28	38	8	26.8	28.6	±0.25	6.2	4.4	±0.15	7.3	±0.20	27.2	28.6	±0.22	5.8	4.4	±0.15	7	±0.20
32	42	8	30.8	32.6	±0.25	6.2	4.4	±0.15	7.3	±0.20	31.2	32.6	±0.22	5.8	4.4	±0.15	7	±0.20
36	46	8	34.8	36.6	±0.25	6.2	4.4	±0.15	7.3	±0.20	35.2	36.6	±0.22	5.8	4.4	±0.15	7	±0.20
40	50	8	38.8	40.6	±0.25	6.2	4.4	±0.15	7.3	±0.20	39.2	40.6	±0.22	5.8	4.4	±0.15	7	±0.20
45	55	8	43.8	45.6	±0.25	6.2	4.4	±0.15	7.3	±0.20	44.2	45.6	±0.22	5.8	4.4	±0.15	7	±0.20
50	60	8	48.8	50.6	±0.25	6.2	4.4	±0.15	7.3	±0.20	49.2	50.6	±0.22	5.8	4.4	±0.15	7	±0.20
28	43	12.5	26.5	28.8	±0.25	9	6.7	±0.15	11.5	±0.20	27	28.9	±0.22	8.5	6.6	±0.15	11.3	±0.20
32	47	12.5	30.5	32.8	±0.25	9	6.7	±0.15	11.5	±0.20	31	32.9	±0.22	8.5	6.6	±0.15	11.3	±0.20
36	51	12.5	34.5	36.8	±0.25	9	6.7	±0.15	11.5	±0.20	35	36.9	±0.22	8.5	6.6	±0.15	11.3	±0.20
40	55	12.5	38.5	40.8	±0.25	9	6.7	±0.15	11.5	±0.20	39	40.9	±0.22	8.5	6.6	±0.15	11.3	±0.20
45	60	12.5	43.5	45.8	±0.25	9	6.7	±0.15	11.5	±0.20	44	45.9	±0.22	8.5	6.6	±0.15	11.3	±0.20
50	65	12.5	48.5	50.8	±0.25	9	6.7	±0.15	11.5	±0.20	49	50.9	±0.22	8.5	6.6	±0.15	11.3	±0.20
56	71	12.5	54.5	56.8	±0.25	9	6.7	±0.15	11.5	±0.20	55	56.9	±0.22	8.5	6.6	±0.15	11.3	±0.20
63	78	12.5	61.5	63.8	±0.35	9	6.7	±0.15	11.5	±0.20	62	63.9	±0.28	8.5	6.6	±0.15	11.3	±0.20
70	85	12.5	68.5	70.8	±0.35	9	6.7	±0.15	11.5	±0.20	69	70.9	±0.28	8.5	6.6	±0.15	11.3	±0.20
80	95	12.5	78.5	80.8	±0.35	9	6.7	±0.15	11.5	±0.20	79	80.9	±0.28	8.5	6.6	±0.15	11.3	±0.20
90	105	12.5	88.5	90.8	±0.35	9	6.7	±0.15	11.5	±0.20	89	90.9	±0.28	8.5	6.6	±0.15	11.3	±0.20
56	76	16	54.2	57	±0.25	11.8	9	±0.15	15	±0.20	54.8	57.4	±0.22	11.2	8.6	±0.15	14.5	±0.20
63	83	16	61.2	64	±0.25	11.8	9	±0.15	15	±0.20	61.8	64.4	±0.22	11.2	8.6	±0.15	14.5	±0.20
70	90	16	68.2	71	±0.35	11.8	9	±0.15	15	±0.20	68.8	71.4	±0.28	11.2	8.6	±0.15	14.5	±0.20
80	100	16	78.2	81	±0.35	11.8	9	±0.15	15	±0.20	78.8	81.4	±0.28	11.2	8.6	±0.15	14.5	±0.20
90	110	16	88.2	91	±0.35	11.8	9	±0.15	15	±0.20	88.8	91.4	±0.28	11.2	8.6	±0.15	14.5	±0.20
100	120	16	98.2	101	±0.35	11.8	9	±0.15	15	±0.20	98.8	101.4	±0.28	11.2	8.6	±0.15	14.5	±0.20
110	130	16	108.2	111	±0.45	11.8	9	±0.15	15	±0.20	108.8	111.4	±0.35	11.2	8.6	±0.15	14.5	±0.20
125	145	16	123.2	126	±0.45	11.8	9	±0.15	15	±0.20	123.8	126.4	±0.35	11.2	8.6	±0.15	14.5	±0.20
140	160	16	138.2	141	±0.45	11.8	9	±0.15	15	±0.20	138.8	141.4	±0.35	11.2	8.6	±0.15	14.5	±0.20
100	125	20	97.8	101.2	±0.45	14.7	11.3	±0.15	18.5	±0.20	98.7	101.8	±0.35	13.8	10.7	±0.15	18	±0.20
110	135	20	107.8	111.2	±0.45	14.7	11.3	±0.15	18.5	±0.20	108.7	111.8	±0.35	13.8	10.7	±0.15	18	±0.20
125	150	20	122.8	126.2	±0.45	14.7	11.3	±0.15	18.5	±0.20	123.7	126.8	±0.35	13.8	10.7	±0.15	18	±0.20
140	165	20	137.8	141.2	±0.45	14.7	11.3	±0.15	18.5	±0.20	138.7	141.8	±0.35	13.8	10.7	±0.15	18	±0.20
160	185	20	157.8	161.2	±0.45	14.7	11.3	±0.15	18.5	±0.20	158.7	161.8	±0.35	13.8	10.7	±0.15	18	±0.20
180	205	20	177.8	181.2	±0.60	14.7	11.3	±0.15	18.5	±0.20	178.7	181.8	±0.45	13.8	10.7	±0.15	18	±0.20
200	225	20	197.8	201.2	±0.60	14.7	11.3	±0.15	18.5	±0.20	198.7	201.8	±0.45	13.8	10.7	±0.15	18	±0.20
160	190	25	157.2	161.5	±0.60	18.5	13.5	±0.20	23	±0.25	158.6	162	±0.45	16.4	13	±0.20	22.5	±0.25
180	210	25	177.2	181.5	±0.60	18.5	13.5	±0.20	23	±0.25	178.6	182	±0.45	16.4	13	±0.20	22.5	±0.25
200	230	25	197.2	201.5	±0.60	18.5	13.5	±0.20	23	±0.25	198.6	202	±0.45	16.4	13	±0.20	22.5	±0.25
220	250	25	217.2	221.5	±0.60	18.5	13.5	±0.20	23	±0.25	218.6	222	±0.45	16.4	13	±0.20	22.5	±0.25
250	280	25	247.2	251.5	±0.60	18.5	13.5	±0.20	23	±0.25	248.6	252	±0.45	16.4	13	±0.20	22.5	±0.25
280	310	25	277.2	281.5	±0.90	18.5	13.5	±0.20	23	±0.25	278.6	282	±0.60	16.4	13	±0.20	22.5	±0.25
320	360	32	316.7	322	±0.90	23.3	18	±0.20	29	±0.25	318.2	323	±0.60	21.8	17	±0.20	28.5	±0.25
360	400	32	357.7	362	±0.90	23.3	18	±0.20	29	±0.25	358.2	363	±0.60	21.8	17	±0.20		±0.25