产品合格证英文怎么写,产品合格证英文模板

首页 > 经验 > 作者:YD1662024-04-03 02:19:58

一)模具专业基本用词 Professional Terms

1.塑料 — plastic, resin

2.样件 — sample

3.钢料 — steel

4.注塑机 — injection machine, press

5. 产品 — part, product, moulding

6.模具 — mold, mould, tool

A 简易模(样板模)— prototype mold

B 量产用模具 — production mold

7.三维造型(数模)—3D model, 3D data

8.二维产品图 — 2D part drawing

9.设计 — design

10.制造 — manufacture, build up, construction, fabrication, make

11.检验 — check, inspection

12.测量 — measure, inspection

13.修改 — change, modify, correction

14.工程更改 — engineer change

15.质量 — quality

16.数量 — quantity

17.基准 — datum, reference

(二)如何解析2D 产品图?How to read 2D part drawing?

一. 产品几何 Geometry

1.点 — point

2.线(边) — line, edge

3.面 face

A 侧面 — side

B 表面 — surface

C 外观面 — appearance surface

4.壁厚 — wall thickness, stock thickness

5.加强筋(骨位) — rib

6.孔 — hole

7.细长的槽 — slot

8.柱位 — boss

9.角 — corner

A 圆角 — fillet

B 倒角 — chamfer

C 尖角 — sharp corner

10.斜度 — angle, taper

11. 凹槽—recess , groove

二. 分模信息 Splitting

1. 分型线 — parting line (P/L), splitting line

2. 主分模方向 — main direction, line of draw

3. 浇口设定 — gating

一. 产品标识 Part Identification

1. 产品名称 — part name (P/N)

2. 产品编号 版本号 — part number revision (Rev.)

3. 型腔号 — cavity number

4. 材料标记 — material symbol

5. 模具编号 — mold number (no.)

6. 日期印 — dating insert, date code

7. 循环印 — cycling code

8. 公司标志 — company logo

二. 技术要求 Specification (Special Requirement)

1. 项目启动表 Kick-off sheet

1) 项目名称 — program name, project name

2) 产品名称 — part name, product name, part description

3) 产品编号 — part number (P/N)

4) 客户模号 — customer mold no.

5) 项目启动日期 — kick off date, start date

6) 项目完成日期 — due date, lead time

7) 内模件用钢 — tool steel

8) 型腔数量 — number of cavities

9) 数据文件编号 — data file no.

10) 注塑材料 — resin, plastic, raw material

11) 收缩率 — shrink, shrinkage, shrink factor

12) 注塑机吨位 — molding machine size, injection machine size

13) 成型周期 — cycle time

14) 型腔光洁度 — cavity polish

15) 型芯光洁度 — core polish

16) 皮纹(晒纹)— texture, grain

17) 拔模斜度 — draft angle, removal taper

18) 注塑件颜色及光泽 — molded color & gloss

19) 模具加工地 — manufacturing facility

20) 热流道供应商 — manifold manufacturer, manifold supplier

21) 浇口位置 — gate location / position

22) 浇口类型 — gate type

产品标识 — stamp information, part identification

特殊要求 — special instructions

1. 产品质量及外观要求 Part Quality & Appearance Requirement

1) 尺寸及公差 Dimension & Tolerance

① 重要尺寸 — critical dimension, important dim., key dim.

② 理论尺寸 — nominal dimension

③ 实际尺寸 — actual dimension

④ 公差 — tolerance

⑤ 公差带 — tolerance range

⑥ 尺寸超差 — dimension deviation

⑦ 接受(合格) — accept, OK

⑧ 拒绝(不合格) — reject, refuse, obsolete, NG

⑨ 让步接受 — concession, special admit

⑩ 返工 — re-work

2) 产品缺陷(常见的)Defects (normal)

① 缩水 — sink mark, shrinkage

② 飞边,毛边 — flash, burr

③ 段差 — mismatch discrepancy

④ 银丝纹,蛇纹 — snake marks, streak

⑤ 弯曲,变形 — warpage, distortion

⑥ 打不饱(缺料) — short shot

⑦ 熔接线 — weld line

⑧ 多胶— unwanted plastic

⑨ 拉伤—damage

2. 产品外观 Part Appearance

① 产品颜色 — part color

② 产品光泽 — gloss

③ 皮纹粒度 — grain

产品合格证英文怎么写,产品合格证英文模板(1)

3. 常用词汇、词组及短语 Normal Word, Short Sentence

1) 单边 — per side

2) 双边 — both sides

3) 加入,添加 — add, incorporate

4) 去除,取消 — remove, cancel

5) 满足…的要求,符合,与…要求一致 — according to, conform to, satisfy, meet

6) 要求,需要 — require, need, demand

7) 确认 — be approved, agreed by …

8) 允许 — permit, allow

9) 在…范围之内 — within

10) 不可以,不允许,禁止 — free from, prevent, avoid

11) …,除非有另指 — … unless otherwise specified

12) …或少于 — …or less

13) 自动化运作 — automatic operation

14) 未注尺寸(详细形状)见三维造型

Non dimensioned contour (detailed shape) see 3D model.

15) 分型线上的飞边(披缝)或段差应小于…

Burrs or discrepancy on the P/L shall be … or less.

标题栏 Title Block

1. 产品名称 — part name

2. 图纸编号 版本号(索引号)— drawing no. level (index)

3. 一般公差 — general tolerance

(三) 如何阅读制模标准?How to read tooling standard?

一.模具结构术语 Mold Construction Terms

A.模架 Mold Base

1. 模架量化特征 Measurement Feature

① 长 X 宽 X 高 — Length X Width X Height

② 模具高度尺寸(模厚) — stack height of mould

③ 模具重量 — total weight of mould, mould thickness

2. 定模底板 — front plate, top clamping plate, clamp plate, clamping plate

3. 定模板 — cavity plate, fixed mould plate, A – plate

4. 动模板 — core plate, moving mould plate, B – plate

5. 支撑板 — support plate, backing plate

6. 间隔板,方铁 — support blocks, rails, risers, spacer block

7. 顶杆固定板 — retaining plate, ejector retaining plate

8. 顶板 — ejector plate,bottom clamping plate

9. 动模底板 — back plate

10.导柱 — guide pillar, leader pin, guide pin

11.导套 — guide bush, leader pin bush

12.复位杆 — return pin, push-back pin

13.弹簧 — spring

14.撑头 — support pillar

15.顶针板导柱、导套 — ejection guide pin / bush

16.垃圾钉 — stop pin, stop button

17. 模脚 — standing-off pillars

18. 标牌 — plaque scutcheon

B.成型零部件 moulding components

1. 型芯 — core insert

2. 型腔 — cavity insert

3. 镶针 — core pin

4. 镶块 — sub-insert, split

5. 滑块 — slide, sliding split

6. 斜顶 — lifter, angled-lift split, loose core

A 斜顶头 — lifter head

B 斜顶杆 — lifter rod, lifter shaft

7. 成型顶杆 — moulding face pin, form pin

C.浇注系统 Feed System

1.塑料 Moulding

a.主流道 — sprue

b.分流道 runner

① 主分流道 — main runner

② 二级分流道 — branch runner

分流道断面形状 cross-sectional shape of runner

① 圆形 — full round

② 半圆形 — semicircular

③ 梯形 — trapezoidal

c.浇口 gate

常用浇口形式 normal gate type :

① 边缘浇口(J型浇口) — edge gate, J – gate

② 侧浇口 — side gate

③ 潜伏式浇口 — sub-gate, subsurface gate, submarine gate, cashew gate

④ 潜伏式二次浇口(隧道式浇口) — tunnel gate onto feeder post

⑤ 点浇口 — pin gate

⑥ 直接浇口(主流道型浇口) — sprue gate, direct gate

⑦ 护耳式浇口 — tab gate

d.模腔 — impression

e. 冷料井 — cold slug well

f. 热流道 — hot runner

2.模具零件 mold components

a.定位圈 — locating ring, location ring, register ring

b.浇口套 — sprue bush

c.挡圈 — stop ring

d.浇口镶块 — gate insert

e.热流道板 — manifold

f. 热嘴 — hot drop\hot sprue

分型面及其锁紧、排气 Parting Surface, inter-locking & venting

1. 分型线 — parting line ( P/L )

2. 镶拼线 — bodyline, joint line

3. 平 / 不平的分型面 — flat / non – flat parting surface

4. 封胶面 — shut off surfaces, seal-off surfaces

5. 擦穿位 — shut off

6. 碰穿位 — kiss-off

7. 管位 — parting line lock

8. 分型面的释放(避空) — relief of parting surface

9. 分型面的平衡 — balancing of parting surface

10.锁紧角度 — locking angle

11.锁紧力 — clamping force

12.锁模块 — safety strap

13.精定位 — Interlock, die lock

14.困气 — air trap

15.排气槽 — vent, vent slot

E.滑块机构 Slide

1.驱动 Actuation

① 斜导柱 — angle pin, horn pin, cam pin

② 弹簧 — spring

③ 油缸 — hydraulic cylinder

2.制动 Detention

① 滑块固定器 — slide retainer

② 弹簧制动器 — spring-loaded detention (plunger)

③ 挡钉、挡板 — stop pin, stop plate, slide stop

3.导轨 — gib, guide strip

4.锁紧块(楔紧块)— heel block, locking heel, wedge block, chase block

5.耐磨片 — wear plate, wear strip

6.压板 — retainer, gib

7.螺钉 — screw

8.定位销 — dowel pin

F.斜顶机构 Lifter

1.斜顶头 — lifter head

2.斜顶杆 — lifter rod, lifter shaft

3.开口销 — split pin

4.固定板(压板) — retainer plate

5.耐磨片 — wear plate

6.铜导套 — bronze bushing

7.衬套 — spacer

8.导轨 — L – gib

9.滑动块 — slide

G.顶出系统 Ejection System

1.基本词汇 Basic Word

① 顶出行程 — ejection stroke

② 模具开档 — daylight

③ 粘模 — stick

④ 产品脱模 — part is push off from, clear part of mould, separation of part

2.顶板机构 Ejector plate assembly

① 顶板 — ejector plate

② 顶板固定板 — retaining plate

③ 推板— stripper plate

④ 推板导柱 — ejector guide pin

⑤ 推板导套 — ejector guide bush

⑥ 撑头 — support pillar

3.复位机构 Return System

① 复位杆(回程杆)— return pin, push – back pin

② 垃圾钉 — stop pin, stop button

③ 压簧 — compressed spring

④ 碟簧 — a stack of ―Belleville‖ washers

⑤ 早复位机构 — early return system

⑥ 强制复位机构 — positive return system

4.顶出方法 Ejection Techniques

1)顶杆顶出 — pin ejection

2)顶管顶出 — sleeve ejection

3)顶块顶出 — bar ejection

4)扁顶顶出 — blade ejection

5)顶板顶出 — stripper ejection

6)油缸顶出 — hydraulic ejection

7)气顶 — air ejection

8)阀门顶出 — valve ejection

5.顶出元件 Ejection Elements

1)拉料杆 — sprue puller, sucker pin

2)顶杆 — ejector pin

3) 阶梯式顶杆 — stepped ejector pin

1)顶管 — ejection sleeve, sleeve

2)扁顶 — ejector blade, slabbed off ejector pin

3)顶块 — stripper bar

4)顶环 — stripper ring

5)推板 — stripper plate

6)加速顶 — accelerated ejection

1.顶出辅助机构 Supplementary operating system

1)弹簧柱塞器 — spring – loaded plunger

2)弹珠定位器 — ball catch system

3)插销式锁扣 — Latch – lock

4)尼龙拉杆装置 — friction puller device

2.电器元件 Electric Components

1)压力传感器 — pressure transducer

2)限位开关 — limit switch

F.冷却系统 Cooling System

1.基本词汇 Basic Word

1)温差 — temperature variation

2)水孔(水道) — waterlines, water-ways, flow-way, channel

3)水路 — cooling circuit

4)水路示意图 — water schematic, schematic circuit

5)冷却液 — coolant, coolant fluid

6)内连接 — interconnect

7)外连接 — external connection

8)出口、入口 — outlet、inlet

9)漏水 — water leakage

2.水路分布 Circuits

1)阶梯式水路 — stepped system

2)分隔板水路 — baffled hole system

3)斜孔式水路 — angled hole system

3. 水路元件 Components

1) 闷头(螺塞、止水栓) — (threadless)brass pressure plug : female plug & male

2) 隔水片 — baffle

3) 密封圈 — O – ring

4) 快插水路接头 — quick disconnect fitting, quick connection adaptor

5) 弯头 — elbow

6) 偶合器(连接器、接头) — adaptor (including a plug & a socket)

7) 橡皮管 — rubber hose

1) 分水板,集水块 — water manifold

G.螺纹、螺纹孔 & 螺钉 Thread, thread hole & screw

1. 螺纹 — thread

2. 管螺纹 — pipe thread

3. 螺纹孔 — screw hole, tapped hole

4. 起吊孔 — handling hole, jack screw hole, eye bolt hole

5. 螺钉 — screw

6. 内六角螺钉 — socket headed cap screw (s.h.c.s.)

7. 沉头螺钉 — flat headed cap screw (f.h.c.s)

8. 螺栓 — bolt

9. 螺母 — nut

10.锁紧螺母 — locknut

11. 螺纹标准 Thread Standard

① 公制标准 — Metric

② 英制标准 — Imperial

③ 英制管螺纹标准 — British Standard Pipe thread (BSP)

④ 美制管螺纹标准 — NPT

⑤ 美制粗螺纹标准 — United Coarse thread (UNC)

⑥ 美制细螺纹标准 — United Fine thread (UNF)

产品合格证英文怎么写,产品合格证英文模板(2)

H.润滑 Lubrication

1. 润滑槽 — grease groove

2. 加油管 — grease line

3. 油杯 — lubrication fitting

I. 测量仪器 Measuring Instruments

1.游标卡尺 — vernier caliper

2.千分尺 — micrometer

3.高度规 — height gauge

4.刻度规 — dial gauge

5.三坐标测量仪(三次元) — Coordinate Measure Machine(CMM)

6.塞规 — pin gauge

7.圆角量规 — radii gauge

8.轮廓投影机—profile projector

J.注塑机参数 Injection Machine Parameter

1.注塑机规格参数 Injection Machine Specification

① 锁紧类型 clamp type

a.油缸 — hydraulic

b.肘杆式 — toggle

② 垂直注塑机导柱间距 — tie bar vertical clearance

③ 水平注塑机导柱间距 — tie bar horizontal clearance

④ 台板尺寸 — platen dim.

⑤ 最小 / 最大模厚 — mold height Min. / Max., Min. / Max. mold thickness

⑥ 最小 / 最大注塑机开档 — open daylight Min. / Max.

⑦ 锁紧行程 — clamp stroke

⑧ 锁紧力 — clamping force

⑨ 顶出行程 — ejector stroke

⑩ 顶出力 — ejector force

栏目热文

文档排行

本站推荐

Copyright © 2018 - 2021 www.yd166.com., All Rights Reserved.